Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing changed? Glance inside the tank, and you could see no water inside. Before you panic, rest easy that repairing this issue is usually easy to accomplish. If you can’t complete this yourself, you can always schedule toilet repair with an experienced plumber. Follow these tips to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first step is to make sure the water is flowing. If you or someone in your household recently completed a toilet repair, you may have turned off the water first. Did you forget to turn it back on? To check, rotate the water shut-off valve on the wall to the rear of the toilet. If the valve was closed, water should now start refilling the tank. If this fails to work, turn on the water at your sink or an alternative plumbing fixture. If nothing comes out from the tap, you could possibly have a bigger water supply issue. Contact your water company to learn more. 

Reposition or Replace the Float Mechanism 

Older toilet brands use a float ball to determine the water level as it rises in the tank. When the ball hits a specified height, the float arm it’s joined to stops the water flow. However, insufficient water might enter the tank if the ball is positioned incorrectly or the arm is faulty. To adjust the float ball, start by removing the toilet tank top. Bend the float arm up slightly to change where it sits in the tank. If this does not fix the problem, you may need to replace the full float mechanism. You should be able to perform this yourself by following the instructions that come with the replacement parts, or you can hire a plumber for help. Just note that float balls are old toilet technology. You may appreciate improved dependability and efficiency if you upgrade the existing tank components or replace the toilet entirely. 

Adjust the Fill Valve 

More recent toilets utilize a float cup in place of a float ball, coupled with a fill valve and water level rod. There may very well be no water in the toilet tank because the valve has slipped out of place or become clogged. Here are some to consider: 

• Adjust the fill valve: Have a look inside the toilet and locate the fill valve on top of a vertical tube device on the left side of the tank. Make sure it’s secure and evenly connected to the tube. Then, adjust the water level. Current models of toilets have an adjustment knob you can turn by hand, while older versions may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and make it possible for the tank refill to verify the water level. Adjust it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other debris may be clogging the valve and keeping your toilet from filling. Turn off the water behind the toilet and remove the fill cap. Then, slowly turn the water back on, cupping your hand over the valve to prevent water from spraying all over the place. After several seconds, turn the water back off. Finally, wash the fill cap to clear away hard water buildup. If the cap is damaged, swap it out. 
• Clean the valve tube: The tube below the fill valve could also be clogged. Shut off the water and remove the valve hardware. Then, stick a slim bottle brush or wire down the tube. Turn the water back on slightly to flush away the junk. Replace the valve hardware and flush the toilet to check your adjustments. 

Repair or Replace the Trip Assembly 

If you’ve attempted the steps above without any luck, the last possibility is a damaged trip assembly. This part links the flush handle to the tank. If it’s broken or positioned improperly, the flush cycle may not complete, leaving the tank void. Take off the toilet tank lid and check the trip assembly fastened to the handle. If it’s out of place, reposition it. If the assembly is crooked, worn or broken, change it out. Whether you complete the job yourself or leave it to a plumber, this uncomplicated repair should get your toilet tank filled with water again. 

Schedule Toilet Repair Today 

You can’t go long without a reliable toilet, so call [Company name] to schedule a toilet repair. We can figure out why your toilet isn’t filling and propose the correct fix. If your plumbing fixture is old and worn out, our team can install a high-efficiency toilet in your home. Rest easy that every plumbing repair and replacement we complete is backed by a 100% satisfaction guarantee. To schedule an appointment from one of our licensed professionals, please contact your neighborhood Service Experts Heating, Air Conditioning & Plumbing office today.